FIX-A- Leak *NOTES*
SUCTION LINE LEAKS:
 Suction Leaks are usually known by air mixed
with the water at the return fittings. In most
cases suction lines only leak water when the
filter pump is shut off. Normal Circulation
well simply draw FIX-A-LEAK away from the leak
and if the pump is shut off the material will
simply not get to the leak. You mast reverse
the flow of water, to force the material through
the leak under pressure. Preferably 5-10 psi.
till the leak has stopped. When this has been
achieved, gradually increase pressure to 15-25
psi. to insure a proper seal.
VERY IMPORTANT:
After sealing a suction line leak 'it' is a
must to leave suction off the repaired line
for no less than 48 hrs. FIX-A-Leak requires
time to cure and harden.
Miscellaneous Leaks:
If you suspect a leak around fittings inside
the pool (such as return fittings) lights, skimmer(s)
or steps, etc. Shut down pump. Apply FIX-A-Leak
directly to the leak using a squeeze bottle,
similar to a ketchup bottle. Allow a minimum
of 48 hrs. to cure before starting up circulation.
PRECAUTION: Keep Out Of Reach Of Children.
Causes severe eye and skin irritation. Do not
get in eyes, on skin, or on clothing. Harmful
or fatal it swallowed. Avoid contamination of
food. Rinse empty container thoroughly with
water and discard it.
FIRST AID:
In case of contact, immediately flush eyes
or skin with plenty of water for at least 15
minutes. For eyes, contact a physician. Remove
and wash contaminated clothing before reuse.
If swallowed, drink milk, egg whites, gelatin
solution. If these are not available drink large
quantities of water. Call a physician immediately.
NOTE:
FIX-A-Leak has been thoroughly field tested
under various weather conditions, and has proven
to be effective in sealing leaks. FIX-A-LEAK
is also an excellent preventative maintenance
aid, as it coats all surfaces that it comes
in contact with, it cuts down on formation of
rust and corrosion. Marlig Industries nor its
Agents assume responsibility for the performance
of this material.
|
|
|
|
GENERAL INFORMATION
FIX-A- Leak
|
:
|
is a blended concentrated material designed
to seal leaks in virtually any material
|
|
|
:
|
can be applied for leaks in the shell and
works equally well in the plumbing
|
|
|
:
|
will seal holes 1/8" in diameter
|
|
|
:
|
will form a permanent seal
|
|
Use 1 quart per pool up to 22,000 gallons.
Do not use in excess of 1 quart per 5000
gallons of water.
|
DIRECTIONS
*Shake Well Before Using*
1.
|
Bypass FILTER MEDIA before adding FIX-A-Leak
to water. Sand Filters: set filter valve
to recirculate Other Types: remove cartridges
DE elements from filter lank. Then proceed
to circulate through empty tank.
|
2.
|
With pump running add FIX-A-LEAK slowly
through skimmer or in front of any other
suction intake.
|
3.
|
After adding FIX-A-LEAK adjust suction
to main drain. If this is not possible,
the vacuum cleaner could be used alternatively,
simply by placing the vacuum in deepest
part of pool and connect to normal vacuum
connection. Set filter valve to normal vacuum
position.
|
4.
|
FIX-A-Leak is very heavy and will sink
to the lowest point rather quickly. It must
be stirred back into suspension, either
manually using a pool broom or mechanically
with an automated pool cleaner every 4-6
hrs. during circulation of water.
|
5.
|
Continue to recirculate water until the
leak has stopped.
|
6.
|
Mark level of water in pool and check for
2-3 days to deter mine d the leak has stopped.
|
7.
|
After the leak has stopped and given the
proper time to cure. (24-48 hrs.)
You may return to normal filtration.
Sand Filters: Set filter valve to filter
and resume normal operation. Backwash
out unused FIX A-Leak as required.
Other Types: Reinstall filter into tank
and Resume operation. Rinse out unused
FIX-A-Leak from filter as required.
*NOTE* Never let cartridges or DE elements
be left to dry before they are cleaned.
|
8.
|
Treatment can be repeated if necessary. |
|
|
|
Fix-A-Leak
for Swimming Pools & Spas
