Solar Sun Rings

What Are Solar Sun Rings? The Solar Sun Ring is a passive solar swimming pool heating device made from two sheets of heavyweight U.V. resistant vinyl. The upper clear layer holds insulating air and focuses sunlight on the blue colored lower layer. The blue layer absorbs about 50% of the sunlight and converts it to heat. The balance of the sunlight is allowed to pass through for deep water heating. Each Sun Solar Ring generates 21,000 BTU per day. Rings are 60" in diameter.

How Do Solar Sun Rings Work? At night the contained air acts as an insulating blanket to retain heat gained during daylight. Solar Sun Rings are equipped with six magnets to improve clarity and decrease hardness of the water in your pool. The magnets are positioned to facilitate rafting. The strength of the magnets will permit single position removal but will easily separate to prevent entrapment in accidental falls.

Solar Sun Rings were designed to be compatible with automatic pool cleaners. In the event the suction hose catches on a ring, the ring will separate from the raft to allow the pool cleaner to continue. Neither water nor pool chemicals can evaporate through the Solar Sun Rings two layers of heavyweight vinyl. You will save water and chemicals about equal to the percentage of the surface covered. Once the water in your pool has reached adequate temperature, Solar Sun Rings may be turned over to conserve water by limiting evaporation without significantly heating the water.

One Ring is $29.99. Buy 5 or more at $24.99 each!

SELECT POOL SIZE & RING AMOUNT. CLICKING LINK WILL ADD RINGS TO CART.

Your pool requires some direct sunlight and open water to stay healthy. The open water around the raft of Solar Sun Rings and the triangle caused by the convergence of three Solar Sun Rings is by design. These open areas allow your pool to receive some direct sunlight. This sunlight will greatly reduce the incidence of mustard algae.

Easily Cleaned - After removal from the swimming pool, Solar Sun Rings can be easily cleaned with a sponge and mild detergent solution.
Warranty: Solar Sun Rings are warranted to be free of manufacturing defects for two years. Warranty is limited to materials and workmanship.

INSTRUCTIONS FOR USE:
Inflation: Inner Grid should be inflated orally with about 2 large breaths of air for an average adult. Don't use more air - two breaths is all that's needed. Close the valve, "bunch up" the Rings to move the contained air around to separate both layers of plastic. The Ring cannot be made to lie flat unless the layers are separated. Each Ring will be about the size of a soccer ball when "bunched" up. The outer ring should be inflated orally until it is firm. Close the valve. Place Rings in a single layer (do not stack) in direct sunlight on a flat, non-abrasive surface until the packing lines relax. This will take approximately 10-30 minutes depending on the intensity of the sun. If the Ring does not lie flat after packing lines are relaxed, examine the Ring for areas where the layers of plastic are not separated & "bunch up" again. If the Ring still doesn't lie flat, measure the diameter. A properly inflated Ring is 60 inches in diameter. If the Ring is smaller than 60", use the deflation tube (provided) to remove air from the inner grid until the Ring lies flat. Excessive air in the inner grid, deep packing lines and failure to separate the two layers may all cause the outer edge of the Ring to curl and distort.

Using Solar Sun Rings for Heating: Once the Rings are inflated, cover 70% - 80% of the surface of your pool with Rings by placing the blue colored side on the water. Do not cover more than 70% of the surface of deep pools; or more than 80% of shallow pools. For the best solar effect, keep the upper surface clean and clear.

Using Solar Sun Rings for Cooling: Turn the Rings over so that the blue side is face-up. Rings do not heat efficiently when turned upside down but will keep direct sunlight off your pool's surface.

Using Solar Rings for Chemical & Water Savings: Water and chemicals cannot evaporate through the two layers of heavyweight vinyl. You will save on water & chemicals in proportion to the percentage of pool surface covered.

Care of Solar Sun Rings: Once inflated, proper care of this product will greatly extend its useful life. While Rings are not in the pool, do not walk on them or drag them - especially on abrasive surfaces such as pool decking. When not in use, do not stack Rings in direct sunlight as this will cause excessive internal temperatures which may melt the vinyl films. Solar Sun Rings are a passive pool heating device; do not use as pool toys.

Solar Sun Rings Features:

Safety: No other floating solar cover matches Solar Sun Rings design for safety. Countless pets and many people have died because of entrapment with the one piece bubble pack covers. The primary design criteria of the Solar Sun Ring was to prevent entrapment.

Durability: Once the design for the Solar Sun Ring was established the material selection began. Polyethylene plastic, which is used for all bubble pack covers, was rejected because of it's intolerance to and degradation in direct sunlight and inability to retain air. High quality ultra violet resistant vinyl (polyvinyl chloride) is used exclusively for durability that cannot be achieved by the inferior plastic used in bubble pack covers. Vinyl will normally outlast polyethylene 3 to 1. The vinyl used to manufacture Solar Sun Rings is not destroyed by pH fluctuation, higher than normal chlorine concentration or salt water systems. Furthermore, vinyl is easily repaired if punctured.

Solar Efficiency: By using the high quality polished vinyl for the top layer and a 50% density lightly frosted lower layer, we achieved a solar efficiency that greatly surpasses bubble pack covers. The milky translucent inferior plastic used in bubble pack covers reflects much of the sun's energy and fails to allow adequate deep water heating. Solar Sun Rings design and materials allow greater solar efficiency with greater nighttime insulation due to greater captive air thickness. Solar Sun Rings were designed to safely heat swimming pools, not cushion packages. The effect is that Solar Sun Rings with 70% to 80% coverage outperform bubble pack covers with 100% coverage.

Mustard Algae: The 100% coverage and inefficient solar effect of bubble pack covers creates additional problems. By blocking all direct sunlight, mustard algae will form within a very short time. This negates the continuous use of the bubble pack covers. The Solar Sun Ring with its increased solar efficiency is designed for continuous use without culturing a pool full of mustard algae.

Compatibility: The Solar Sun Ring is designed to be compatible with automatic pool cleaners. The many features that give Solar Sun Rings greater safety at the same allow them to be used with automatic pool cleaners. Solar Sun Rings are also compatible with solar panel systems giving a pool a double shot of the sun's energy during the day and great nighttime insulation.

Placement and Removal: Solar Sun Rings were designed for easy placement and removal by one person. The magnets for conditioning the water are placed into the perimeter of each ring to facilitate rafting. The five foot diameter of each ring also allows for easy cleaning.

Aesthetics: I have never heard anyone praise the aesthetics of the bubble pack cover. Solar Sun Rings were designed to add festive colors to an otherwise drab device. The silk screen printing of the Solar Sun Rings is similar to a window screen to allow solar heating while adding color to the swimming pool.

Storage: Because the solar thermal genesis and insulation properties of Solar Sun Rings is so great, when they are removed from the pool, they must be stored out of direct sunlight to prevent overheating.